Rupert Neve 5052 Mic Pre / Inductor EQ
Preampificatore microfonico e EQ a induzione – solo verticale
The Shelford 5052 echoes the simple and definitive 1073 feature set with a vertically-oriented mic pre, high pass filter, and 3-band inductor EQ, while also incorporating modern capabilities like the variable Silk / Texture control from the Portico II Series and simultaneous pre / post “tape” operation. Utilizing class-A, discrete, +/- 24V topologies with custom-wound transformers and inductors, Rupert Neve designed the 5052 as a vintage-style channel strip that captures the soul of his classic designs, without the previous compromises.
The Mic Pre
Like Rupert’s designs from his time in Shelford, the 5052 preamplifier has 72dB of discrete, class-A gain coupled with serious square-core transformers. Unlike the classics however, the output transformer features the Silk Red / Blue and Texture controls from the Portico II Series to hone the harmonic content and tonality of the output stage. By engaging these controls and sufficiently driving the output, the 5052 can produce up to 4-5% THD (primarily 2nd order, some 3rd order), bringing a richness and thickness to tracks when desired with no danger of overloading the output stage. With Silk disengaged, the output is modern and pristine, yet still retains Rupert’s signature larger-than-life transformer sound. The mic pre section also includes a sweepable 20-250Hz high-pass filter, Mic / Line selection, 48V phantom power, and polarity reverse.
Dual I/O Paths
Following the preamplifier, the 5052 has a transformer-coupled output, which allows the 5052 to feed a tape machine or DAW directly from the mic pre while still using the EQ and Silk / Texture in a dedicated analogue mix path such as that found with a 5088, 5060 or vintage console. This output can also be used to insert a separate compressor between the mic pre and the EQ, or it can allow the 5052 to work with two separate sources. When the “TO EQ” button is engaged, the mic pre signal is routed directly into the EQ such that the mic / line input signal flows through to the main output as a single channel strip.
The “best of the classics” EQ
The 3-band, custom-tapped inductor EQ on the 5052 was inspired by RND’s favorite portions of Rupert’s vintage EQ designs. The low frequency band is primarily based on the 1064, which is renowned for its creamy, resonant bass. Unlike the 1064 however, the LF band on the 5052 can be used as either a shelf or a peak filter, adding punch, dimension, and immense control to your low end. The 5052’s inductor midrange band is based on his prized 1073 EQ, which is ideal for sweetening vocals and instruments while bringing them forward in a mix. Additionally, the mid frequency band’s proportional “Q” response makes it well-suited for minimizing problematic frequencies in a source. The 5052’s high frequency band is a hybrid vintage / modern design, blending inductor circuitry from the 1073 with capacitor-based topologies to achieve the vintage tones with enhanced control. As Rupert originally intended with his most prized classic designs, each EQ section uses low-feedback, class-A discrete electronics to prevent low-level artifacts and harshness from detracting from the tonal shaping. The EQ circuit itself, however, is a decidedly modern updated design using techniques and components that were simply not available 35 years ago, and should not be considered a “clone”.
Power, Connections and Mounting
The 5052 receives +/- 24V rails from an external DC power supply using a 4-pin connection. There are currently two options available: the RND 5-way brick supply and the RND 25-way 2U rack-mount supply. The back panel of the 5052 includes three XLR-F connections for Mic In, Line In, and EQ In, and two XLR-M connections for Mic Out and Main Out. The 5052 chassis is a “half-rack” format, and can be mounted in RND’s new 2 –way and 4-way vertical racks in addition to the existing 9-way racks and the 5088 penthouse.
A complete discussion on transformers is out of place at this point, but it is helpful to review some of the essentials where it will be seen that a design needs to be viewed as a whole, not simply from the point of view of a single component.
The fine subtleties of circuit design relating to sonic performance are gradually becoming more clearly understood. For example, research has shown conclusively that frequencies above 20 kHz affect the way in which humans perceive sound quality. But, long before scientific evidence emerged a substantial body of musicians and engineers knew that equipment with apparently the same technical measurements could sound very different.
Incredibly small amounts of musically dissonant odd harmonics have a disastrous effect on the sound quality. Extraneous noise or interference that finds its way into a signal path seriously impairs performance of the whole chain.
Many control rooms make use of outboard gear that is not well protected from external signals. Poor grounding of such equipment can be a serious problem. “Electronically balanced” circuits much used in modern equipment, can give very good measurements on the test bench but they do not provide adequate rejection of the stray fields found in every working environment.
Input and output circuits must be freed from ground dependence so that only the “wanted” signal enters and leaves the processing path. Transformers are the ideal solution. The sweet and silky sound of my classic old favorite consoles was achieved with big transistors and large high quality transformers. Rupert Neve Designs Portico modules achieve similar quality today without the bulk or the cost.
In order that modules can work together as would be expected (i.e. in a proprietary console configuration) without producing hum, R.F. interference, or other interactions, the connecting interfaces, grounding, levels and impedances must receive careful attention. Each of our Shelford modules is a complete integral signal processor that delivers its specified performance independently. This is one of the reasons we use transformers.
Main Output, no load, –3 dB @ 2.5 Hz
–3 dB @ 125 kHz
Measured at Main Output, unweighted, 22Hz-22kHz, Terminated 40 Ohms, With gain at unity
better than –102 dBu
from 20 Hz to 20 kHz, +25 dBu.
from 20 Hz to 20 kHz is +25 dBu. Total Harmonic Distortion and Noise: from <10 Hz to 80 kHz,
@ 1kHz, +20 dBu output: Better than 0.002% @ 20Hz, +20 dBu out Better than 0.120%
@ 20kHz, +20 dBu out Better than 0.010%
Measured at Main Output, unweighted, 22Hz-22kHz, Terminated 40 Ohms. with all gains set at 0,
Better than –92 dBu
from 20 Hz to 20 kH, +24.5 dBu
from 20 Hz to 20 kHz, +24.5 dBu
Total Harmonic Distortion and Noise:
from <10 Hz to 80 kHz, @ 1kHz, +20 dBu output: Better than 0.007% @ 20Hz, +20 dBu out Better than 0.120% @ 20kHz, +20 dBu out Better than 0.070%
25-Way Power Supply (2U)
5-Way Power Supply
2-Way Wood Rack
9-Way Metal Rack
Neve serie Shelford
In conformità con quanto previsto dal Decreto Legislativo 6 settembre 2005 n. 206 (e successive modifiche ed integrazioni), il cliente Consumatore, ove non soddisfatto dei prodotti ovvero del contenuto dei servizi acquistati presso il Venditore, potrà restituire i prodotti medesimi o rinunciare al diritto alla prestazione dei servizi ed ottenere il rimborso del prezzo già corrisposto in sede di pagamento anticipato.
Il diritto di recesso-restocking è applicabile solo ed esclusivamente per acquisti operati da persone fisiche (consumatore) e quindi per acquisto di beni non utilizzati professionalmente e per vendite iniziate e risolte a distanza.
Gli articoli acquistati possono essere resi entro 14 giorni successivi alla consegna dei prodotti ovvero entro i 14 giorni successivi all’acquisto dei beni o dei servizi, inviando una comunicazione via raccomandata A.R. all’indirizzo via F. Sabatini, 10 – 00135 Roma, contenente tutte le informazioni necessarie ed utili ad una corretta elaborazione della pratica di restituzione e rimborso.
Tale comunicazione dovrà necessariamente contenere tutto quanto di seguito indicato:
a. l’espressa volontà del Cliente di voler recedere in tutto o in parte dal contratto di acquisto;
b. il numero e la copia del documento (fattura – documento di trasporto) comprovante l’acquisto dell’ordine rispetto al quale si intende esercitare il diritto di recesso;
c. la descrizione ed i codici dei Prodotti rispetto ai quali si esercita il diritto di recesso.
Il riaccredito, comprensivo delle spese di spedizione, verrà effettuato dal Venditore entro 14 giorni dalla ricezione della comunicazione via raccomandata A.R. sopra citata.
Sono tuttavia esclusi dal diritto di recesso i seguenti articoli:
Prodotti audiovisivi o i software informatici sigillati, aperti dal consumatore
Beni confezionati su misura o chiaramente personalizzati
Il materiale dovrà ritornare integro e completo dell’imballo originale e dei manuali d’uso.
Le spese di spedizione per il reso delle apparecchiature sono a carico del consumatore.
Per maggiori informazioni: